Show simple item record

dc.contributor.authorChang, Hongli
dc.date.accessioned2022-09-22T16:32:47Z
dc.date.available2022-09-22T16:32:47Z
dc.date.issued2022-05
dc.identifier.urihttp://hdl.handle.net/11122/13007
dc.descriptionDissertation (Ph.D.) University of Alaska Fairbanks, 2022en_US
dc.description.abstractHeavy oil reservoirs on Alaska North Slope (ANS) are unconsolidated and contain abundant clay minerals, where the first-ever field pilot is currently implemented to validate the use of polymer floods for heavy oil enhanced oil recovery (EOR). The polymer molecules and/or fine clay particles carried with the produced liquid could potentially affect the oil/water separation, which is one of the major concerns for field operators. This dissertation aims to investigate the emulsification behavior of produced liquid, understand the emulsifying mechanism, and seek an adaptive and cost-effective method to treat the produced liquid from polymer flooding. Emulsions were prepared by mechanically mixing the actual heavy oil and the produced water from the pilot site, of which the stability was investigated by bottle test method or multiple light scattering method. Drop size distribution and interfacial properties were measured via microscope and pendant drop technique to probe the stability mechanism further. Results showed that oil-continuous or water-continuous emulsion could be generated depending on the water cut, clay types, clay concentration, and polymer concentration. In the crude oil/water system, the increasing water cut triggered the phase inversion of oil-continuous emulsion to water-continuous emulsion, resulting in faster separation and lower emulsion stability. Whereas, clay particles, no matter added to the oil or water phase, resulted in an unfavorable phase inversion from the loose watercontinuous emulsion to the tight oil-continuous emulsion as clay concentration increased. For all four types of clay except Ca-montmorillonite, clay particles added to water led to an earlier phase inversion and higher emulsion stability than that added to the oil. The dual function of polymer on emulsion stability was observed. On the one hand, both sheared and unsheared polymer tended to convert the oil-continuous emulsion formed in either crude oil/water system or complex crude oil/water/clay particle system to the water-continuous emulsion, acting as a weak demulsifier to accelerate the oil/water separation. On the other hand, the addition of polymer to the watercontinuous emulsion could result in enhanced emulsion stability, which is primarily attributed to the increased viscosity of the continuous phase and the decreased drop size of the dispersed oil phase. Particularly, the sheared polymer had a weaker ability to stabilize the o/w emulsion than the unsheared polymer due to the lower viscosity of the sheared polymer solution resulting from the breakdown of the polymer macromolecules. As for the chemical demulsification tests, the performance of demulsifiers showed a complex dependency upon the water cut, the shearing intensity, demulsifier type and dosage, and the polymer concentration. A compound emulsion breaker, E12+E18, exhibited the most satisfactory demulsification performance despite the varied test conditions. For severe water-continuous emulsions that might require a multi-fold dosage of demulsifier, a less expensive electrolyte, KCl, was proposed to be used in combination with demulsifier E12+E18 to improve the demulsification performance. In the proposed demulsifier formula, the effectiveness of the commercial demulsifier relied on its destructive effect on the interfacial film, while the efficacy of KCl was mainly dependent on its viscosity reduction effect on the continuous phase. This dissertation illustrates that intermediate layer elimination and water clarification are the major challenges for produced liquid treatment from polymer flooding. It also provides practical and theoretical guidance in advance for the demulsification strategy of the produced liquid from the ongoing first-ever polymer flooding pilot on ANS.en_US
dc.description.sponsorshipU.S. Department of Energy (DOE) - National Energy Technology Laboratory under Award Number DE-FE0031606 and Hilcorp Alaska, LLCen_US
dc.description.tableofcontentsChapter 1 Introduction -- Chapter 2. Experimental investigation on separation behavior of heavy oil emulsion for polymer flooding on Alaska North Slope -- Chapter 3. Emulsification characteristics and electrolyte-optimized demulsification of produced liquid from polymer flooding on Alaska North Slope -- Chapter 4. Effect of clay particles and polymer on crude oil emulsion formation and stability -- Chapter 6. Conclusions and recommendations.en_US
dc.language.isoen_USen_US
dc.subjectPolymer floodingen_US
dc.subjectHeavy oilen_US
dc.subjectNorth Slopeen_US
dc.subject.otherDoctor of Philosophy in Engineeringen_US
dc.titleStudy on emulsification/demulsification behavior and mechanism of produced liquid from polymer flooding on Alaska North Slopeen_US
dc.typeDissertationen_US
dc.type.degreephden_US
dc.identifier.departmentDepartment of Petroleum Engineeringen_US
dc.contributor.chairZhang, Yin
dc.contributor.chairDandekar, Abhijit
dc.contributor.committeeTrainor, Tom
dc.contributor.committeeGuerard, Jennifer


Files in this item

Thumbnail
Name:
Chang_H_2022.pdf
Embargo:
2024-04-12
Size:
9.585Mb
Format:
PDF

This item appears in the following Collection(s)

Show simple item record